aseptic technique raises a handful of sensible questions. This page answers them in order, starting with the fundamentals and moving to applications.
This page was last updated on 2026-08-01 and is reviewed periodically as new material appears.
Temperature logs and cold-chain documentation help identify excursions that may compromise a batch. Automated freezers, desiccant packs, and sealed containers limit moisture and frost accumulation. Aliquoting small portions before freezing reduces the number of times the main stock changes temperature. Labels should include peptide name, lot, concentration if known, solvent, and date prepared. Periodic analytical verification by high-performance liquid chromatography or mass spectrometry can detect degradation, truncation, or sequence errors that visual inspection cannot reveal.
Practical handling begins with an inventory record that links each vial to a lot number, synthesis date, and purity certificate. Before opening a container, allow it to equilibrate to room temperature to prevent condensation on the powder. Weighing or transferring should occur in a low-humidity environment using tools that minimize static and adsorption. Hygroscopic peptides may gain water quickly, changing mass and concentration estimates. Recording the container's initial mass and any visible changes supports later reconciliation of material.
Reconstitution introduces additional variables: solvent choice, pH, ionic strength, and filtration. Many sequences dissolve readily in water, while hydrophobic ones may need acetonitrile, dimethyl sulfoxide, or a small amount of base. Adding solvent slowly and avoiding vigorous vortexing can reduce foaming and shear-induced aggregation. If the solution appears cloudy, filtration may remove particulates but can also remove aggregated peptide and alter concentration. A clear solution does not by itself confirm correct sequence or purity, so analytical checks remain necessary.
After reconstitution, solutions are usually divided into single-use aliquots to avoid repeated freeze-thaw cycles. Aliquots should be labeled with peptide identity, concentration, solvent, and date, then stored at the temperature specified by the supplier or protocol. Many peptides tolerate -20 °C for short periods, while -80 °C is preferred for longer storage. Frost-free freezers are generally avoided because temperature fluctuations can stress samples. Aseptic technique and sterile filters reduce microbial contamination, though filtration can also remove aggregated material or bind some peptides.
Peptide handling begins with careful receipt and inventory. Containers should be inspected for damage, label information should match the certificate of analysis, and storage location should be recorded. Many lyophilized peptides are electrostatic and may cling to vial walls or weighing paper, which can complicate transfer. Allowing a cold vial to equilibrate to room temperature before opening reduces condensation on the contents. Clean tools, gloves, and a low-humidity workspace limit contamination and moisture exposure during manipulation.
| Property | Value | Notes |
|---|---|---|
| Container material | Glass or polypropylene | Glass is relatively inert but can adsorb; polypropylene may leach. |
| Headspace gas | Argon or nitrogen | Inert gas displaces oxygen for oxidation-prone sequences. |
| Equilibration before opening | 20–30 minutes at room temperature | Sealed vial warms gradually to reduce condensation. |
| Typical aliquot size | Small working portions | Limits repeated temperature cycling of the main stock. |
| Documentation fields | Lot, date, solvent, concentration | Supports traceability and degradation monitoring. |
Cold-chain shipping uses insulated containers, phase-change packs, and temperature indicators. Dry ice maintains -70 °C or lower but requires venting to avoid pressure buildup. Gel packs provide 2-8 °C for shorter transit. Upon arrival, recipients should record temperature indicators and transfer vials promptly to storage. Deviations from specified conditions should be documented and may require analytical re-check. The effect of a brief temperature excursion is peptide-specific and not always predictable from general rules.
Handling begins with receipt and inspection. Vials should be checked for damage, label integrity, and temperature history. Lyophilized peptides should be allowed to equilibrate to room temperature before opening to prevent condensation. Solutions should be prepared in a clean, calibrated environment using appropriate solvents. Personal protective equipment and containment reduce exposure and contamination. Documentation of lot number, date, and storage location supports traceability. The goal is to limit repeated temperature changes, moisture exposure, and microbial contamination.
Reconstitution solvent depends on peptide solubility and intended use; water, buffer, or small amounts of organic solvent may be needed. After dissolution, solutions are typically aliquoted into single-use portions to avoid repeated freeze-thaw cycles. Aliquots are stored at -20 °C or -80 °C, depending on stability. Labels include concentration, solvent, date, and operator. Sterile filtration may be used when microbial control is required, but filters can adsorb peptides. The optimal concentration and solvent are often determined empirically.
After reconstitution, solutions are divided into single-use aliquots and stored at -80°C. Labels include peptide name, concentration, buffer composition, date, and lot number. Freeze-thaw cycles are minimized by thawing only the needed aliquot on ice or at room temperature. Some peptides benefit from the addition of a carrier protein, such as bovine serum albumin, or a cryoprotectant like glycerol to reduce adsorption to plastic. Glass vials with low-binding surfaces are preferred for dilute solutions. Shipping of frozen aliquots uses dry ice and insulated containers to maintain the cold chain.
Receiving a peptide shipment requires immediate inspection of the packaging and temperature indicators. Any deviation from the specified cold chain should be documented and investigated. Upon arrival, solid peptides are generally kept at -20°C, whereas liquid formulations are stored at -80°C. Vials should be kept upright and protected from light. Repeated warming and cooling of the entire container is avoided by preparing smaller working aliquots. A log of lot numbers, receipt dates, and storage locations supports traceability and quality control.
Reconstitution is a critical handling step. The appropriate solvent—often sterile water, phosphate-buffered saline, or a water-acetonitrile mixture—is chosen based on peptide solubility. Adding solvent gently down the vial wall and swirling, rather than vortexing, reduces foaming and shear stress. The resulting solution should be clear; visible particles indicate incomplete dissolution or contamination. Concentration is recorded accurately because it affects subsequent use. If the peptide is not fully soluble, a small amount of organic solvent or a different buffer may be required, but this changes the final composition.
Albumin is a family of globular proteins, the most common of which are the serum albumins. All of the proteins of the albumin family are water-soluble, moderately soluble in concentrated salt solutions, and experience heat denaturation. Albumins are commonly found in blood plasma and differ from other blood proteins in that they are not glycosylated. Substances containing albumins are called albuminoids. A number of blood transport proteins are evolutionarily related in the albumin family, including serum albumin, alpha-fetoprotein, vitamin D-binding protein and afamin. This family is only found in vertebrates. Albumins in a less strict sense can mean other proteins that coagulate under certain conditions. See Other albumin types for lactalbumin, ovalbumin and plant "2S albumin". Albumins in general are transport proteins that bind to various ligands and carry them around. Human types include:
The origins of alemtuzumab date back to Campath-1 which was derived from the rat antibodies raised against human lymphocyte proteins by Herman Waldmann and colleagues in 1983. The name Campath derives from the pathology department of Cambridge University. Initially, Campath-1 was not ideal for therapy because patients could, in theory, react against the foreign rat protein determinants of the antibody. To circumvent this problem, Greg Winter and his colleagues humanised Campath-1, by extracting the hypervariable loops that had specificity for CD52 and grafting them onto a human antibody framework. This became known as Campath-1H and serves as the basis for alemtuzumab. While alemtuzumab started life as a laboratory tool for understanding the immune system, within a short time it was clinically investigated for use to improve the success of bone marrow transplants and as a treatment for leukaemia, lymphoma, vasculitis, organ transplants, rheumatoid arthritis and multiple sclerosis.
The linear amino acid sequence of a protein is called the primary structure. The primary structure can be easily determined from the sequence of codons on the DNA gene that codes for it. In most proteins, the primary structure uniquely determines the 3-dimensional structure of a protein in its native environment. An exception is the misfolded prion protein involved in bovine spongiform encephalopathy. This structure is linked to the function of the protein. Additional structural information includes the secondary, tertiary and quaternary structure. A viable general solution to the prediction of the function of a protein remains an open problem. Most efforts have so far been directed towards heuristics that work most of the time.
Benazepril (Lotensin) Cilazapril (Inhibace) Enalapril (Vasotec/Renitec/Berlipril/Enap/Enalapril Profarma) Imidapril (Tanatril) Lisinopril (Listril/Lopril/Novatec/Prinivil/Zestril, Lisidigal) Moexipril (Univasc) Perindopril (Coversyl/Aceon/Perindo) Quinapril (Accupril) Ramipril (Altace/Prilace/Ramace/Ramiwin/Triatec/Tritace/Ramitac) Trandolapril (Mavik/Odrik/Gopten) Ceronapril (never marketed) Fosinopril (Fositen/Monopril) ACE inhibitor peptides can be derived from natural sources such as algae, fruit, seeds, dairy and animal products. A comprehensive resource on anti-hypertensive peptides is available in the form of a database. It contains around 1700 unique antihypertensive peptides. Arfalasin (HOE 409) is an angiotensin antagonist.
Degradation of an amino acid often begins with transamination, in which its amino group is transferred to α-ketoglutarate, forming glutamate. This process involves transaminases, often the same enzymes used in amino acid synthesis. In many vertebrates, the amino group is subsequently released as ammonia and converted to urea via the urea cycle for excretion. However, amino acid degradation can result in uric acid or ammonia instead, depending on the organism. For example, serine dehydratase converts serine directly to pyruvate and ammonia. After removal of one or more amino groups, the remaining carbon skeleton of an amino acid can serve as a precursor for synthesizing other amino acids, be further metabolized for energy after conversion into intermediates of glycolysis (typically via gluconeogenesis) or of the citric acid cycle, or be used for fatty acid synthesis and storage as triacylglycerol. Amino acids are bidentate ligands, forming transition metal amino acid complexes.
Sources: en.wikipedia.org
Acta Biochimica et Biophysica Sinica (ABBS) is a peer-reviewed scientific journal which publishes original research articles, short communications, and reviews in the fields of biochemistry and biophysics. Established in 1958, the journal is sponsored by the Institute of Biochemistry and Cell Biology, an institute of the Chinese Academy of Sciences, and is published monthly by Oxford Journals and was published by Blackwell Publishing prior to January 2009. This journal is indexed in the following databases: Science Citation Index Expanded Zoological Record BIOSIS Previews Chemical Abstracts Service – CASSI Index medicus MEDLINE PubMed
Immunomodulating agents regulate the immune system's response and are produced by various immune cells. These agents include the following agents and markers: The BCG vaccine has been used against tuberculosis, mycobacteria, and various cancers in the form of vaccination as an initial immune system stimulant. In cancer, the anti-tumor immunological effects are elicited by the host's immune response and the BCG infection against the tumor cells, most commonly in bladder cancer. The immune activation allows for further recognition and elimination of malignant tumor cells. Specific active immunotherapy administers a specific antigen as the therapy. The therapy allows the host to create an antigen-specific response with the development of antibodies, proliferation of cytotoxic T lymphocyte responses, or both, directed at the desired pathogen or malignant tumor cell in the case of cancer therapy.
European Union officials, European ministers and Commissioner (Tonio) Borg set up an urgent meeting in Brussels on 13 February 2013 on how to contain the horse meat scandal that exposed flaws in European control systems on food safety, and to formulate an action plan. Following the meeting, EU agriculture ministers announced a three-month coordinated control plan of DNA testing of processed meat across the European Union. The plan, adopted 19 February 2013, called for 2,500 random tests on processed food for horse DNA and 4,000 for phenylbutazone (bute), beginning in March 2013, with initial results announced on 15 April 2013. The Hague-based Europol would handle the co-ordination of investigations among national authorities, as well as any raids on premises and arrests on suspicion of criminal conspiracy to defraud.
Blood sugar regulation is the process by which the level of blood sugar, the common name for glucose dissolved in blood plasma, is maintained by the body within a narrow range. This tight regulation is referred to as glucose homeostasis. Insulin, which lowers blood sugar, and glucagon, which raises it, are the most well known of the hormones involved, but more recent discoveries of other glucoregulatory hormones have expanded understanding of this process. The pancreas gland secretes two hormones that are primarily responsible for regulation of glucose levels in blood. Blood sugar levels are regulated by negative feedback in order to keep the body in balance. The levels of glucose in the blood are monitored by many tissues, but the cells in the pancreatic islets are among the most well understood and important. Granule docking is an important glucose-dependent step in human insulin secretion that does not work properly in type 2 diabetes.
In the phosphatidylinositol signal pathway, the extracellular signal molecule binds with the G-protein receptor (Gq) on the cell surface and activates phospholipase C, which is located on the plasma membrane. The lipase hydrolyzes PIP2 into two second messengers: inositol 1,4,5-trisphosphate (IP3) and diacylglycerol (DAG). IP3 binds with the IP3 receptor in the membrane of the smooth endoplasmic reticulum and mitochondria to open Ca2+ channels. DAG helps activate protein kinase C (PKC), which phosphorylates many other proteins, changing their catalytic activities, leading to cellular responses. The effects of Ca2+ are also remarkable: it cooperates with DAG in activating PKC and can activate the CaM kinase pathway, in which calcium-modulated protein calmodulin (CaM) binds Ca2+, undergoes a change in conformation, and activates CaM kinase II, which has unique ability to increase its binding affinity to CaM by autophosphorylation, making CaM unavailable for the activation of other enzymes. The kinase then phosphorylates target enzymes, regulating their activities. The two signal pathways are connected together by Ca2+-CaM, which is also a regulatory subunit of adenylyl cyclase and phosphodiesterase in the cAMP signal pathway.
Sources: en.wikipedia.org
The right side of a positive-sensed AAV genome encodes overlapping sequences of three capsid proteins, VP1, VP2 and VP3, and two accessory proteins, MAAP & AAP, which start from one promoter, designated p40. The molecular weights of these proteins are 87, 72 and 62 kiloDaltons, respectively. The AAV capsid is composed of a mixture of VP1, VP2, and VP3 totaling 60 monomers arranged in icosahedral symmetry in a ratio of 1:1:10, with an empty mass of approximately 3.8 MDa. The crystal structure of the VP3 protein was determined by Xie, Bue, et al.
Human serum albumin is the main protein of human blood plasma. It makes up around 50% of human plasma proteins. It binds water, cations (such as Ca2+, Na+ and K+), fatty acids, hormones, bilirubin, thyroxine (T4) and pharmaceuticals (including barbiturates). Its main function is to regulate the oncotic pressure of blood. The isoelectric point of albumin is 4.7. Alpha-fetoprotein is a fetal plasma protein that binds various cations, fatty acids and bilirubin. Vitamin D-binding protein binds to vitamin D and its metabolites, as well as to fatty acids. Afamin binds vitamin E. It seems to carry lipidated Wnt proteins and Vitamin E around. Extracellular matrix protein 1 is a less canonical albumin. It regulates bone mineralization. The four canonical human albumins are arranged on chromosome 4 region 4q13.3 in a tandem manner.
ACC Synthase is 450-516 amino acid long sequence depending on the species of plant from which it is extracted. Though it is comparable in the species in which it is found, its COOH-terminal domain is more variable, leading to differences such as oligomerization. The COOH-terminal domain is responsible for oligomerization. In most ACC Synthase producing cells, ACC Synthase exists as a dimer. However, in some we find a monomer ("which is more active and efficient [than its dimer counterpart"). The structure of ACS has been largely determined via X-ray crystallography. Conservation of the residues in ACS's catalytic domain and sequence homology suggest that ACS catalyzes the synthesis of ACC in a similar fashion as other enzymes that require PLP as a cofactor. However, unlike many other PLP-dependent enzymes, Lys (278) is not the only residue that interacts with the substrate. The proximity of the electronegative oxygen from Tyr (152) to the C-γ-S bond suggests a crucial role in the formation of ACC. X-ray crystallography with aminoethoxyvinylglycine (AVG) a competitive inhibitor confirmed Tyrosine's role in the γ elimination. As of late 2007, 6 structures have been solved for this class of enzymes, with PDB accession codes PDB: 1B8G, PDB: 1IAX, PDB: 1IAY, PDB: 1M4N, PDB: 1M7Y, and PDB: 1YNU.
Protein inhibition by inhibitor binding may induce obstruction in pathway regulation, homeostatic regulation and physiological function. Competitive inhibitors compete with substrate to bind to free enzymes at active sites and thus impede the production of the enzyme-substrate complex upon binding. For example, carbon monoxide poisoning is caused by the competitive binding of carbon monoxide as opposed to oxygen in hemoglobin. Uncompetitive inhibitors, alternatively, bind concurrently with substrate at active sites. Upon binding to an enzyme substrate (ES) complex, an enzyme substrate inhibitor (ESI) complex is formed. Similar to competitive inhibitors, the rate at product formation is decreased also. Lastly, mixed inhibitors are able to bind to both the free enzyme and the enzyme-substrate complex. However, in contrast to competitive and uncompetitive inhibitors, mixed inhibitors bind to the allosteric site. Allosteric binding induces conformational changes that may increase the protein's affinity for substrate. This phenomenon is called positive modulation. Conversely, allosteric binding that decreases the protein's affinity for substrate is negative modulation.
Cells require a full and functional cellular machinery to live. When they belong to complex multicellular organisms, they need to communicate among themselves and work for symbiosis in order to give life to the organism. These communications between cells triggers intracellular signaling cascades, termed signal transduction pathways, that regulate specific cellular functions. Each signal transduction occurs with a primary extracellular messenger that binds to a transmembrane or nuclear receptor, initiating intracellular signals. The complex formed produces or releases second messengers that integrate and adapt the signal, amplifying it, by activating molecular targets, which in turn trigger effectors that will lead to the desired cellular response.
Sources: en.wikipedia.org
Work quickly in a dry environment and keep the container closed when not in use. Equilibrate sealed vials to room temperature before opening to reduce condensation. Record mass changes, as absorbed water can affect concentration calculations.
Liquid storage is generally shorter than dry storage because water enables hydrolysis, oxidation, and microbial growth. If solution storage is necessary, use sterile technique, appropriate pH, and cold temperatures. Aliquot to avoid repeated temperature changes.
Reversed-phase high-performance liquid chromatography is common for purity assessment, while mass spectrometry confirms molecular mass and can reveal modifications. Amino acid analysis or sequencing may be used when sequence information is critical. These methods complement visual inspection and storage records.
It should first equilibrate to room temperature in a sealed container to prevent condensation on the cold contents. Opening too soon can introduce moisture and reduce stability, and the waiting period depends on vial size and packaging.