aliquoting raises a handful of sensible questions. This page answers them in order, starting with the fundamentals and moving to applications.
Reviewed 2025-12-19. Anything still debated is marked as such rather than presented as settled.
Handling begins with receipt and inspection. Vials should be checked for damage, label integrity, and temperature history. Lyophilized peptides should be allowed to equilibrate to room temperature before opening to prevent condensation. Solutions should be prepared in a clean, calibrated environment using appropriate solvents. Personal protective equipment and containment reduce exposure and contamination. Documentation of lot number, date, and storage location supports traceability. The goal is to limit repeated temperature changes, moisture exposure, and microbial contamination.
Reconstitution solvent depends on peptide solubility and intended use; water, buffer, or small amounts of organic solvent may be needed. After dissolution, solutions are typically aliquoted into single-use portions to avoid repeated freeze-thaw cycles. Aliquots are stored at -20 °C or -80 °C, depending on stability. Labels include concentration, solvent, date, and operator. Sterile filtration may be used when microbial control is required, but filters can adsorb peptides. The optimal concentration and solvent are often determined empirically.
Cold-chain shipping uses insulated containers, phase-change packs, and temperature indicators. Dry ice maintains -70 °C or lower but requires venting to avoid pressure buildup. Gel packs provide 2-8 °C for shorter transit. Upon arrival, recipients should record temperature indicators and transfer vials promptly to storage. Deviations from specified conditions should be documented and may require analytical re-check. The effect of a brief temperature excursion is peptide-specific and not always predictable from general rules.
Peptide handling begins with careful receipt and inventory. Containers should be inspected for damage, label information should match the certificate of analysis, and storage location should be recorded. Many lyophilized peptides are electrostatic and may cling to vial walls or weighing paper, which can complicate transfer. Allowing a cold vial to equilibrate to room temperature before opening reduces condensation on the contents. Clean tools, gloves, and a low-humidity workspace limit contamination and moisture exposure during manipulation.
Reconstitution is the process of dissolving a dried peptide in a suitable solvent. The choice of solvent depends on solubility, charge, and sequence; sterile water is common, while buffers or small amounts of organic solvent may be needed for hydrophobic peptides. Adding solvent gently down the vial wall and mixing by inversion or gentle swirling reduces foaming and shear. Vortexing or vigorous pipetting can denature some peptides or promote aggregation. The resulting solution should be visually inspected for particles, turbidity, and complete dissolution before use.
After reconstitution, solutions are usually divided into single-use aliquots to avoid repeated freeze-thaw cycles. Aliquots should be labeled with peptide identity, concentration, solvent, and date, then stored at the temperature specified by the supplier or protocol. Many peptides tolerate -20 °C for short periods, while -80 °C is preferred for longer storage. Frost-free freezers are generally avoided because temperature fluctuations can stress samples. Aseptic technique and sterile filters reduce microbial contamination, though filtration can also remove aggregated material or bind some peptides.
| Property | Value | Notes |
|---|---|---|
| Form | Lyophilized powder or frozen solution | Powder is generally more stable for long-term storage. |
| Recommended storage | -20 °C, desiccated, protected from light | -80 °C for solutions or sensitive sequences. |
| Reconstitution solvent | Water, buffer, or organic co-solvent | Choice depends on peptide solubility and assay. |
| Freeze-thaw stability | Limited; avoid repeated cycles | Aliquoting into single-use portions reduces damage. |
| Contamination control | Aseptic technique and sterile filtration | Filters may adsorb peptides; validate recovery. |
Reconstitution introduces additional variables: solvent choice, pH, ionic strength, and filtration. Many sequences dissolve readily in water, while hydrophobic ones may need acetonitrile, dimethyl sulfoxide, or a small amount of base. Adding solvent slowly and avoiding vigorous vortexing can reduce foaming and shear-induced aggregation. If the solution appears cloudy, filtration may remove particulates but can also remove aggregated peptide and alter concentration. A clear solution does not by itself confirm correct sequence or purity, so analytical checks remain necessary.
Temperature logs and cold-chain documentation help identify excursions that may compromise a batch. Automated freezers, desiccant packs, and sealed containers limit moisture and frost accumulation. Aliquoting small portions before freezing reduces the number of times the main stock changes temperature. Labels should include peptide name, lot, concentration if known, solvent, and date prepared. Periodic analytical verification by high-performance liquid chromatography or mass spectrometry can detect degradation, truncation, or sequence errors that visual inspection cannot reveal.
Receiving a peptide begins with recording its identity, lot number, quantity, and arrival condition. Dry material is often kept in sealed containers with desiccant and an inert headspace to limit moisture and oxygen. Containers should be compatible with the peptide and solvent; some peptides adsorb to certain plastics or glass. Labels should include date, concentration, solvent, and storage location. A centralized inventory with temperature logs helps prevent loss and mix-ups.
Reconstitution involves adding a solvent to dry peptide, often water or a buffered solution. The chosen liquid should match the peptide's solubility and intended assay, and it should be free of contaminants. Gentle mixing or inversion reduces foaming and shear, which can damage some peptides. If the peptide does not dissolve readily, adjusting pH or using a small amount of organic co-solvent may help. The final solution is typically clarified before use in analytical or laboratory procedures.
After reconstitution, solutions are usually divided into single-use aliquots to limit repeated handling. Each aliquot is stored at a temperature appropriate for the peptide, with -20 °C or -80 °C common for longer-term laboratory storage. Freeze-thaw cycles are minimized because they can cause aggregation, precipitation, or loss of activity. Temperature monitoring and documented storage conditions support reproducibility across experiments. When a peptide is removed from storage, it is typically allowed to equilibrate before opening to reduce condensation.
Dyneins, one of the three major classes of motor protein, are AAA proteins which couple their ATPase activity to molecular motion along microtubules. The AAA-type ATPase Cdc48p/p97 is perhaps the best-studied AAA protein. Misfolded secretory proteins are exported from the endoplasmic reticulum (ER) and degraded by the ER-associated degradation pathway (ERAD). Nonfunctional membrane and luminal proteins are extracted from the ER and degraded in the cytosol by proteasomes. Substrate retrotranslocation and extraction is assisted by the Cdc48p(Ufd1p/Npl4p) complex on the cytosolic side of the membrane. On the cytosolic side, the substrate is ubiquitinated by ER-based E2 and E3 enzymes before degradation by the 26S proteasome.
The Society holds an annual conference in late May or early June as well as topical conferences (at Asilomar State Beach in California and Sanibel Island, Florida) and a fall workshop, which is also focused on a single topic. Conferences on Mass Spectrometry and Allied Topics have been held yearly since 1953. International Mass Spectrometry Foundation List of female mass spectrometrists ASMS website
Most commonly 2,5-diketopiperazines are generated by cyclisation of dipeptides. In addition to the many methods of peptide synthesis, the Ugi reaction can be applied. Dipeptides with an ester terminus spontaneously cyclize often. Racemization can be problematic. The Ugi reaction using an isonitrile, amino acid, aldehyde and amine, can produce a dipeptide in equally high yield and optical purity, to that formed by standard peptide couplings. Commonly, an isonitrile is chosen to give a labile terminal amide to enable cyclization. For example, the direct 2,5-DKP ring formation via such an activated leaving group using the stable, easily accessible and versatile convertible isonitrile 1-isocyano-2-(2,2-dimethoxyethyl)-benzene 4 gave a one-pot synthesis of N-substituted 2,5-diketopiperazine's 7.
Sources: en.wikipedia.org
ALK-positive ALCL is diagnosed by histological and immunological examinations of involved tissues, typically lymph nodes. These tissues have lymphoma-like infiltrates that have variable numbers of ALCL "hallmark" cells, i.e. cells with kidney- or horseshoe-shaped nuclei that strongly express CD30 as detected by immunohistochemistry and an ALK fusion protein as detected by fluorescence in situ hybridization. These cells are scattered throughout the infiltrates. WHO classifies these infiltrates into 5 patterns: a common pattern consisting of large variably shaped cells with large nuclei that typically contain multiple nucleoli (60–70% of cases); a small-cell pattern consisting of small to medium-sized neoplastic cells with clear cytoplasm and "hallmark" cells that are concentrated around small blood vessels (5–10% of cases); a lymphohistiocytic pattern consisting of small neoplastic cells along with abundant histiocytes (10% of cases); a Hodgkin's-like pattern in which the architecture resembles the nodular sclerosis pattern of Hodgkin lymphoma (3% of cases); and a composite pattern consisting of two or more of the just described patterns (15% of cases). Detection of circulating autoantibody against ALK supports the diagnosis. Individuals with low levels of these autoantibodies are at an increase risk of relapsing after treatment.
APHL monitors trends in public health laboratory diagnostics, personnel and infrastructure. It uses this data to benchmark against national norms and to define issues of importance to lab practice and policy. APHL also disseminates research findings via issue briefs and communications with federal decision makers, health partners and the laboratory community. Members have access to survey data online, enabling them to leverage this information quickly to identify promising strategies and practices. In an effort to improve laboratory practice, APHL provides free resources, such as tools kits that explain how to: Write a laboratory quality manual Conduct an internal audit Recruit students in STEM fields Deal with laboratory floods In addition to on-demand research and reports, APHL provides continuing education courses to help laboratory scientists keep up with emerging trends, and innovative testing techniques. Training sessions are conducted through conferences, seminars, workshops and online courses.
Knowledge includes experiences of people in the organization, company reports, case histories, databases and other repositories In order for organizations to become agile, organizations, they need to focus on building knowledge bases and cultivating a well trained and motivated workforce. Such an organization is driven by knowledge and information available and possessed by the workforce. This epitomizes the notion that `knowledge is power'. "The ability to control the new product introduction process from the conceptualization and design stages through manufacturing to shipment and product support requires the exploitation of a knowledge-rich work force and sophisticated information technology in most industrial sectors"
Alfred Ellis Wilhelmi (1910–1994) was an American endocrinologist recognized for contributing to the understanding of anterior pituitary hormones. Born in Lakewood, Ohio, Wilhelmi attended Cleveland public schools. Wilhelmi earned a B.S. degree in premedical sciences from Western Reserve University in 1933. He then attended Oxford University as a Rhodes Scholar, where he obtained a B.A. in 1933 and Ph.D. in animal physiology in 1937. He then joined Yale University's Biochemistry Department, rising to the position of Professor in 1950. Wilhelmi chaired the Department of Biochemistry at Emory University School of Medicine from 1950 to 1977. In 1960, he was named Charles Howard Candler Professor of Biochemistry. In 1979, he received Emory's Thomas Jefferson award for service to the university and community. Wilhelmi also was President of the Endocrine Society from 1968 to 1969. During his career, he published over 80 articles in scientific journals.
Sources: en.wikipedia.org
No. Allowing the sealed vial to equilibrate to room temperature reduces condensation on the powder. Condensation can introduce moisture and promote degradation. Equilibration usually takes 15 to 30 minutes depending on vial size.
Aliquoting limits repeated freeze-thaw cycles that can cause aggregation or loss. Single-use portions reduce contamination risk and handling variability. It also allows separate testing without disturbing the main stock.
Inspect packaging, temperature indicators, and vial condition before storage. Record any deviations from the expected temperature range. If a deviation occurred, analytical testing may be warranted before use.
It should first equilibrate to room temperature in a sealed container to prevent condensation on the cold contents. Opening too soon can introduce moisture and reduce stability, and the waiting period depends on vial size and packaging.